Brand Listings


3Pcs Original Hiland DIY Multifunction Transistor Tester Kit For LCR ESR PWM Generator M328 Thumbnail

3Pcs Original Hiland DIY Multifunction Transistor Tester Kit For LCR ESR PWM Generator M328

Product Description - 3Pcs DIY Multifunction Transistor Tester Kit For LCR ESR Transistor PWM Signal Generator M328 Feature: A key measurement operation auto power off delay . Shutdown current is only 20nA, support battery operation. Automatic detection PNP and NPN type bipolar transistors N, P -channel MOSFET, JFET FET diodes two diodes, thyristors resistors capacitors inductors. Automatic detection pin definitions. Measurement of the bipolar transistor current amplification factor (B) and conduction voltage emitter junction (Uf). Darlington transistor may be identified by the amplification factor of the high threshold voltage and high current. Can be detected inside the bipolar transistor and MOSFET protection diodes and displayed on the screen. The threshold voltage and the MOSFET gate capacitance measurement. Support two measuring resistors the potential can also be measured . If the potentiometer is adjusted to its end the tester can not distinguish the two ends of the pin and the middle. Resistance measurement resolution is 0.1Ohm the highest measurement value of 50MOhm. Capacitance measurement range from 25pf to 100mF (100000UF). Resolution up to 1PF. Can detect more than 2UF capacitor equivalent series resistance (ESR) with a resolution of 0.01Ohm. This feature is very important for the detection capacitor performance. You can display symbols of the two diodes in the right direction also shows the forward voltage drop. LED detection of diode forward voltage drop higher than normal . Dual LED detected as double diodes. Simultaneous detection of light-emitting diodes will flash. Each test time is about two seconds only large capacitance and inductance measurements will take a long time. New conversation function, you can select the following additional functions via the menu: 1. The square wave signal generator, optional built-in within the range of 1HZ-2MHZ stall square wave signal; 2.PWM pulse signal generator for 1-99% of the pulse width modulated signal; 3. The frequency meter function, can test 1HZ-25KHZ or higher frequency signal (in this case a slight decline in accuracy, this feature should make their own extensions) Specification: Measurement Range: Resistor: 0.5 ~ 50M Capacitor: 30pF ~ 100mF Inductance: 0.01MH ~ 10H Working voltage: can use 6FF22 9V Battery, or DC 5.5V ~ 12V via DC socket Controller: ATmega328 (has been programmed) Standby current: 0.02uA Operating Current: 13mA (when test current is about 18mA) Note: When measuring 1 uF non-polarity capacitance, attention to short-circuit capacitance between two feet and put off storage of electricity when measuring capacitance, otherwise may damage the instrument, if measuring instrument with electricity is easily to make display show CELL and can't use normally, we are not responsible for this kind of situation, what you can do is replacing the chip, it is important to note, please. Please download the install manual file from here because it is easily damaged especially for the beginner. Package included: 3 x Meter Tester DIY Kit (without the battery, not soldered) Signal generator function PWM pulse signal generator {more}

Brand - Hiland
Model - 953264

Product Price - 28.33 $

Order 3Pcs Original Hiland DIY Multifunction Transistor Tester Kit For LCR ESR PWM Generator M328

Original Hiland DIY M12864 Graphics Version Transistor Tester Kit LCR ESR PWM Thumbnail

Original Hiland DIY M12864 Graphics Version Transistor Tester Kit LCR ESR PWM

Product Description - If you need the chip of this kit: >>>SKU300959<<< Product title marked 'DIY kit' of both parts, you need your own assembled by soldering, to demonstrate for convenience, the main products picture is a physical map, the second picrure are all parts that you receive, be sure to pay attention to distinguish Description: 1. Resistors, capacitors, inductors, diodes, transistors, SCR, and most commonly used devices will automatically recognize and measure 2. The capacitance line measurement capacity and ESR 3. The square-wave generator 4.PWM pulse signal generator 5. Frequency meter function 6. The graphical display of measurement results, easy and intuitive, the whole function is performed by a rotary encoder switch control, easy to operate. Feature: Power supply voltage: DC 5.5-12V Working Current: 24mA @ 9V PCB Size: 75 x 63 mm Main Function: 1. One key measurement operation, auto power off delay. Shutdown current is only 20nA, support for battery operation 2: Automatic detection of PNP and NPN bipolar transistor, N, P-channel MOSFET, JFET field effect transistors, diodes, two diodes, thyristors, resistors, capacitors, inductors. Automatic detection of current amplification factor (B) Pin Definitions and turn-on voltage of the transistor and the emitter junction (Uf) Darlington transistor through a high threshold voltage and high current gain recognition. 3: Can detect bipolar transistors and MOSFET internal protection diode and displayed on the screen. It can be measured threshold voltage and the gate capacitance of the MOSFET. 4: Support two resistance measurements, the potential can also be measured. The highest resolution is 0.1 ohm resistance measurements, the highest measured value of 50M Euro. 5: Capacitance measurement range from 25pf to 100mF (100,000 UF). Resolution up to 1 pF. 0.09UF capacitance can be detected above the equivalent series resistance (ESR) a resolution of 0.01 ohms. To display the value of the capacitor voltage loss and increase the capacitance of a separate line ESR measurements, available online (on the circuit) direct measurement capacitor value and ESR, easy maintenance and troubleshooting capacitance. 6. Inductance measurement range of 0.01MH-20H, otherwise it will be displayed as resistance, if the inductor DC resistance higher than 2100 will be displayed as the European resistance. 7. Can two diode display symbols in the right direction, displaying the forward voltage drop. LED detected as a diode forward voltage drop higher than normal. Dual LEDs detected as double diode. Simultaneous detection LED flashes, very intuitive. 8. Each test of time is about two seconds, only the large capacitance and high inductance measurements will take a long time Additional Feature: 1. The square wave signal generator, optional built-in within the range of 1HZ-2MHZ stall square wave signal; 2.PWM pulse signal generator for 1-99% of the pulse width modulated signal; 3. The frequency meter function, can test 1HZ-25KHZ or higher frequency signal (in this case a slight decrease in accuracy) How to install: http://img.banggood.com/file/products/20151016033628SKU273392.doc Package included: 1 x DIY M12864 Graphics Version Transistor Tester Kit LCR ESR PWM 1 x Case {more}

Brand - Hiland
Model - 997023

Product Price - 18.79 $

Order Original Hiland DIY M12864 Graphics Version Transistor Tester Kit LCR ESR PWM

Original Hiland 0-28V 0.01-2A Adjustable DC Regulated Power Supply DIY Kit Short Circuit Current Limiting Protection Thumbnail

Original Hiland 0-28V 0.01-2A Adjustable DC Regulated Power Supply DIY Kit Short Circuit Current Limiting Protection

Product Description - Feature: Input voltage: 24V AC or 30V DC Output voltage: 0 to 28V adjustable Output current: 0.01A - 2A adjustable Fast rotary encoder: 0.5V, 0.05A Slow rotary encoder: 0.1V, 0.01A Note: 1. The power supply kit can be used as a constant current power supply output voltage. 2. current value can be preset. Current can be pre-set maximum current value in the circuit When turned on in order to avoid damage. 3. A temperature fault fan control switch is turned on (the default is 50 degrees) Power production belongs to the high voltage large current circuit, please be sure to carefully, otherwise may cause harm to the personal safety. Information please look here: 1. files.banggood.com/SKU422723%20manual.doc 2. files.banggood.com/2016/Hiland installation.pdf Package included: 1 x Power Supply DIY Kit {more}

Brand - Hiland
Model - 1060253

Product Price - 16.12 $

Order Original Hiland 0-28V 0.01-2A Adjustable DC Regulated Power Supply DIY Kit Short Circuit Current Limiting Protection

Original Hiland DIY M8 LC Digital Inductance Capacitance Meter Kit Thumbnail

Original Hiland DIY M8 LC Digital Inductance Capacitance Meter Kit

Product Description - Feature: Inductance measuring range: 0.1H-2H Capacitance measurement range: 1pF-2.5F Electrolytic capacitor measuring range: 0.1F-30000F How to use: Plugging in an external power supply (recommended 9V or 12V) that is switched into calibration status (in this case measuring terminal can not access devices); display SET OK After calibration is complete, then press the button to switch to a different measurement, C & L-COM small measure capacitance and inductance, COM-CE measuring electrolytic capacitors, the measured value is displayed directly on the screen. Package included: 1 x DIY M8 LC Digital Inductance Capacitance Meter Kit (the 3 pin connector does not includes) {more}

Brand - Hiland
Model - 976437

Product Price - 14.86 $

Order Original Hiland DIY M8 LC Digital Inductance Capacitance Meter Kit

Original Hiland DIY M12864 Graphics Version LCR ESR PWM Transistor Tester Kit Thumbnail

Original Hiland DIY M12864 Graphics Version LCR ESR PWM Transistor Tester Kit

Product Description - If you need the Supporting Shell for this kit, please check this, http://www.banggood.com/Supporting-Shell-For-DIY-M12864-Graphics-Version-Transistor-Tester-Kit-p-989949.html If you need the chip of this kit: >>>1002733<<< Product title marked 'DIY kit' of both parts, you need your own assembled by soldering, to demonstrate for convenience, the main products picture is a physical map, the second picrure are all parts that you receive, be sure to pay attention to distinguish Description: 1. Resistors, capacitors, inductors, diodes, transistors, SCR, and most commonly used devices will automatically recognize and measure 2. The capacitance line measurement capacity and ESR 3. The square-wave generator 4.PWM pulse signal generator 5. Frequency meter function 6. The graphical display of measurement results, easy and intuitive, the whole function is performed by a rotary encoder switch control, easy to operate. Feature: Power supply voltage: DC 5.5-12V Working Current: 24mA @ 9V PCB Size: 75 x 63 mm Main Function: 1. One key measurement operation, auto power off delay. Shutdown current is only 20nA, support for battery operation 2: Automatic detection of PNP and NPN bipolar transistor, N, P-channel MOSFET, JFET field effect transistors, diodes, two diodes, thyristors, resistors, capacitors, inductors. Automatic detection of current amplification factor (B) Pin Definitions and turn-on voltage of the transistor and the emitter junction (Uf) Darlington transistor through a high threshold voltage and high current gain recognition. 3: Can detect bipolar transistors and MOSFET internal protection diode and displayed on the screen. It can be measured threshold voltage and the gate capacitance of the MOSFET. 4: Support two resistance measurements, the potential can also be measured. The highest resolution is 0.1 ohm resistance measurements, the highest measured value of 50M Euro. 5: Capacitance measurement range from 25pf to 100mF (100,000 UF). Resolution up to 1 pF. 0.09UF capacitance can be detected above the equivalent series resistance (ESR) a resolution of 0.01 ohms. To display the value of the capacitor voltage loss and increase the capacitance of a separate line ESR measurements, available online (on the circuit) direct measurement capacitor value and ESR, easy maintenance and troubleshooting capacitance. 6. Inductance measurement range of 0.01MH-20H, otherwise it will be displayed as resistance, if the inductor DC resistance higher than 2100 will be displayed as the European resistance. 7. Can two diode display symbols in the right direction, displaying the forward voltage drop. LED detected as a diode forward voltage drop higher than normal. Dual LEDs detected as double diode. Simultaneous detection LED flashes, very intuitive. 8. Each test of time is about two seconds, only the large capacitance and high inductance measurements will take a long time Additional Feature: 1. The square wave signal generator, optional built-in within the range of 1HZ-2MHZ stall square wave signal; 2.PWM pulse signal generator for 1-99% of the pulse width modulated signal; 3. The frequency meter function, can test 1HZ-25KHZ or higher frequency signal (in this case a slight decrease in accuracy) Manual ... Package included: 1 x DIY M12864 Graphics Version Transistor Tester Kit LCR ESR PWM {more}

Brand - Hiland
Model - 986954

Product Price - 13.89 $

Order Original Hiland DIY M12864 Graphics Version LCR ESR PWM Transistor Tester Kit

Original Hiland 86 Plastic Shell plus DIY Multifunction Transistor Tester Kit For LCR ESR PWM Generator M328 Thumbnail

Original Hiland 86 Plastic Shell plus DIY Multifunction Transistor Tester Kit For LCR ESR PWM Generator M328

Product Description - If you need the chip of this kit: >>>>>SKU197963<<<<< Feature: A key measurement operation auto power off delay . Shutdown current is only 20nA, support battery operation. Automatic detection PNP and NPN type bipolar transistors N, P -channel MOSFET, JFET FET diodes two diodes, thyristors resistors capacitors inductors. Automatic detection pin definitions. Measurement of the bipolar transistor current amplification factor (B) and conduction voltage emitter junction (Uf). Darlington transistor may be identified by the amplification factor of the high threshold voltage and high current. Can be detected inside the bipolar transistor and MOSFET protection diodes and displayed on the screen. The threshold voltage and the MOSFET gate capacitance measurement. Support two measuring resistors the potential can also be measured . If the potentiometer is adjusted to its end the tester can not distinguish the two ends of the pin and the middle. Resistance measurement resolution is 0.1Ohm the highest measurement value of 50MOhm. Capacitance measurement range from 25pf to 100mF (100000UF). Resolution up to 1PF. Can detect more than 2UF capacitor equivalent series resistance (ESR) with a resolution of 0.01Ohm. This feature is very important for the detection capacitor performance. You can display symbols of the two diodes in the right direction also shows the forward voltage drop. LED detection of diode forward voltage drop higher than normal . Dual LED detected as double diodes. Simultaneous detection of light-emitting diodes will flash. Each test time is about two seconds only large capacitance and inductance measurements will take a long time. New conversation function, you can select the following additional functions via the menu: 1. The square wave signal generator, optional built-in within the range of 1HZ-2MHZ stall square wave signal; 2.PWM pulse signal generator for 1-99% of the pulse width modulated signal; 3. The frequency meter function, can test 1HZ-25KHZ or higher frequency signal (in this case a slight decline in accuracy, this feature should make their own extensions) Specification: Measurement Range: Resistor: 0.5 ~ 50M Capacitor: 30pF ~ 100mF Inductance: 0.01MH ~ 10H Working voltage: can use 6FF22 9V Battery, or DC 5.5V ~ 12V via DC socket Controller: ATmega328 (has been programmed) Standby current: 0.02uA Operating current: 25mA Note: When measuring 1 uF non-polarity capacitance, attention to short-circuit capacitance between two feet and put off storage of electricity when measuring capacitance, otherwise may damage the instrument, if measuring instrument with electricity is easily to make display show CELL and can't use normally, we are not responsible for this kind of situation, what you can do is replacing the chip, it is important to note, please. Please download the install manual file from here because it is easily damaged especially for the beginner. Description: Model: 86-1602 Type: 86 Material: PVC This plastic shell is suitable for DIY Meter Tester Kit, all the LCD1602 screen product, and it can install 5 Nixie tube. Notice: You need to trepanning for the switch, because this shell is Molding products, you need to DIY yourself Package included: 1 x Meter Tester DIY Kit (without the battery, not soldered) 1 x 86 plastic shell {more}

Brand - Hiland
Model - 956240

Product Price - 10.19 $

Order Original Hiland 86 Plastic Shell plus DIY Multifunction Transistor Tester Kit For LCR ESR PWM Generator M328

Original Hiland DDS Function Signal Generator Module DIY Kit Pulse Sine Wave Thumbnail

Original Hiland DDS Function Signal Generator Module DIY Kit Pulse Sine Wave

Product Description - If you need the power, please click : >>> 1022517 <<< And >>> http://forum.banggood.com/forum-topic-123630.html <<< Description: Delicated high speed (HS) signal output up to 8MHz DDS signal with variable amplitude and offset DDS signals: sine, square, saw, rev saw ,triangle, ECG and noise 2 x 16 LCD menu, intuitive 5 button keypad Frequency adjusting steps: 1, 10, 1000, 10000MHz Restoring last configuration after power up Has two outputs-one for DDS signal and another for high speed aquare signal Material: PCB + Electronic Components Power Supply: +5V / +12V / -12V Menu Displey: 2 x 16 LCD HS Signal Frequency: 1, 2, 4, 8MHz Red Board Size: 8 x 8cm / 3.15 x 3.15in (L * W) Screen Size: 6.5 x 1.5cm / 2.6 x 0.6in (L * W) Document: https://www.dropbox.com/s/z0ktc666sct1gj1/H11887install.pdf?dl=0 Package included: 1 x DDS Function Signal Generator {more}

Brand - Hiland
Model - 958215

Product Price - 10.16 $

Order Original Hiland DDS Function Signal Generator Module DIY Kit Pulse Sine Wave